JEL Ltd

Taiwan - Product Safety Testing

For the Information Technology Equipments to be exported and sold in Taiwan, product safety tests have been required since July 1, 2005, therefore we should comply with both of the applicable standards for safety and EMC, and should have BSMI certification ("Official Journal No.09304608410" issued on R.O.C. 93-10-29)
JEL tie up with BSMI accredited product safety test laboratories in Taiwan and other local agents. Therefore we can offer consistent services such as EMC testing in Japan, product safety tests, and certificate acquisition services.

For customers who have CB report

Report Exchanging Service from CB Report to CNS Report

(There are cases that application service for some edition of product safety standards are not available at JEL)

Flow of the test

Inquiry
next

Please contact us with following information:

  • Description of EUT (Specifications, etc.)
  • Rough schedule for preparation of test sample
Reply
next

JEL inform customers of the following information:

  • Reserved day for test*
  • Number of necessary samples
  • Necessary documents list
  • Rough estimation of cost
  • Rough estimation of schedule

* After confirmation of availability at local test laboratory, we will inform the schedule for the test.

Application for Test
next

Please fill in the application form for the certification test and submit it to us. If you have any questions in the application, please contact to the following address:

JEL Asia Approval Group
TEL: +81 4 7188 6381 / FAX: +81 4 7188 6382
e-mail: otoiawase@jel.co.jp

Reservation fixed
next

We will send back a copy to customers with receipt mark stamped. Then the reservation is fixed.

In case you do not receive any confirmation of reservation, please contact to the following address.

JEL Asia Approval Group
TEL: +81 4 7188 6381
e-mail: otoiawase@jel.co.jp

Shipment of sample unit
next

Please arrange shipment of sample unit to the test laboratory or JEL agent prior to the reserved day.

We will advise the shipping address when sending back the application form to you as a confirmation of reservation. Please be sure to attach the operation guide to the sample unit.

Submission of necessary documents
next
Please provide us with necessary documents for issuing test report when you ship the sample. Specifically, please refer to the Necessary Documents List.
Product Safety Test
next
Test at local laboratory
Customers will be updated by JEL with test status as necessary.
Issue of Product Safety Test Report Test report is issued by local laboratory according to the provided documents and test data.

Necessary Documents List for BSMI Endorsed Product Safety Test Report

Item Descriptions
Operation Guide In Traditional Chinese
Important Parts List -
Specifications of important parts, Certificate, Certification Number -
Image of Important parts

Photo image with:
- certification number(s) of the certified parts
- a scale put aside

Wiring block diagram, PCB pattern diagram

-
PCB Layout, Insulation level -
Specifications of Temperature sensor and Overload sensor -
Certificates for Rust preventive paint and plastic material -
Material of the screw -
Type of inner wiring, Manufacturer, Layout, etc. -
Rating Plate Label in Traditional Chinese (Type, voltage, power consumption)
EUT Image (Front & Rear) Photo image with a scale put aside
Sample (  units) Number of units varies by a product.
   
Others -

Note) Necessary document varies by EUT. There are cases that some of above are not required for product safety test.

JEL Applicable CNS Standards

Information Technology Equipments (ITE) CNS 14336 (IEC 60950)
Electronic Apparatus CNS 14408 (IEC 60065)
Household Electrical Appliances CNS 3765 (IEC 60335)

The test for other categories than above will be available at tied-up laboratory. Please feel free to contact us for details. If you are not sure which BSMI category the product belongs to, we recommend that you utilize, "BSMI Confirmation Service", which enables you to check directly with BSMI if the product should be certified or not, by receiving the product specifications prior to the test.

Prices and Lead time

For product safety tests, the cost and lead time differ by product to be tested. Please refer to the following table and contact us if you need further information.

Product Safety Test Fee Approx. JPY300,000`
(The cost varies by each product, for which please ask us, eparately).
BSMI endorsed Test Report issuing fee

Original: Included in above test fee
Photocopied original: JPY3,000/copy

Shipping charge of samples Shipping charge varies by size and weight of EUT.
  1. Lead time varies by products.
  2. It is possible for us to expedite issuing the test report if customer can provide us with necessary documents before finishing the test procedure.

For details please contact to:
yReservation DeskzGeneral Service Bureau / Asia Approval Group
TEL: +81 4 7188 6381
FAX: +81 4 7188 6382
e-mail: otoiawase@jel.co.jp